Connected Competence Knowledge Only Tests

A Knowledge Only Test takes place at HTL’s ECITB approved Test Centre and typically lasts one hour. It is important before attending the test session to revise your knowledge of the subject area. You will be asked to show photo ID, provide your NI number, email address and complete the ECITB data consent form. HTL will take a digital photo of you for ECITB records. The test is taken on a computer or tablet with no supporting materials or use of assistance from smartphones or your own tablet. HTL will operate a clear desk policy and invigilate your test session. The Invigilator is present purely to administer the test session and will not provide training or guidance on the test content. No assistance can be given to a candidate during the test by other candidates or the Invigilator.

ECITB Connected Competence – Knowledge Only Tests
ECITB

Locations

Cramlington, Northumberland

Prices From

£65 + VAT

Course Duration

1.5 Hours

Who Should Attend?

Connected Competence standardises base competence and training requirements for the offshore and site workforce in the UK. It streamlines training, increases the base level of competence and assists with the efficient transfer of employees between companies.

Course Content

HTL offers a complete range of ECITB Connected Competence Knowledge Only Tests:

Appointed Person Moving Loads

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Rigging Workplace Hazards
  • Regulations and Documentation
  • Calculations
  • Rigging Tasks
  • People involved in Rigging activities

Electrical Maintenance

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Electrical Workplace Hazards
  • Electrical Hazardous Area/EX equipment
  • Protection Methods
  • Electrical Hand Tools
  • Transformers and Chokes
  • Circuit Protective Devices
  • Generators
  • AC electrical motors
  • Lighting Equipment
  • Electrical Maintenance Testing

Mechanical Maintenance

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Hydraulic Systems
  • Pneumatic Systems
  • Compressed Air Systems
  • Bearings and Seals
  • Pumps
  • Mechanical Actuating Mechanisms
  • Belt and Chain Drives
  • Shafts and Couplings
  • Clutches
  • Brake Systems
  • Valves
  • Diesel Engines
  • HVAC Systems
  • Diagnosing Mechanical Faults in Explosive Atmospheres

Plating

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Plating Workplace Hazards
  • Interpret Engineering Drawings
  • Marking Out Plate and Structural Steelwork
  • Preparing plate edges using portable edge preparation machines
  • Setting out plate work and structural steelwork
  • Interpret Drawing Information, Fabricate and Install Platework

Electrical Installation

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Electrical Workplace Hazards
  • Electrical Hazardous Area/EX
  • Electrical Installation Testing
  • Lighting Equipment
  • Transformers and Chokes
  • Earthing Equipment
  • Emergency Lighting
  • Electrical Distribution Systems
  • AC Electrical Motors

Instrument & Controls Maintenance

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Instrument and Controls Testing
  • Level Measurement System
  • Flow Measurement Systems
  • Temperature Measurement Systems
  • Fire & Gas Detection Systems
  • Process System Control Valve Assemblies
  • Pneumatic Process Controllers
  • Programme Logic Control Systems
  • Distributed Control Systems
  • Protection Methods for Instruments in Hazardous Areas
  • Analysers
  • Fluid Powered Systems

Pipefitting

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Pipefitting Workplace Hazards
  • Interpret Drawing Information, Fabricate and Install Pipework
  • Preparing and Assembling Welded Pipework
  • Preparing and Assembling Screwed Pipework
  • Fabricating and Installing Pipework Supports
  • Preparation and Testing of Pipework Systems

Rigging

The multi-choice questions will cover the main areas and topics as highlighted below:

  • Workplace Hazards
  • Rigging Workplace Hazards
  • Regulations and Documentation
  • Rigging Equipment
  • Rigging Tasks
  • People involved in Rigging activities

Next Course Starts In

Our latest schedule for this course is not available online. Please use the button below to enquire about our next available dates.

Ask a Question

Upcoming Courses

Related Courses